no photo
Bulk Wire
It never hurts to have a little extra wire on hand, so MSD offers the 8.5mm Super Conductor in bulk length. No terminals or boots are supplied.
6 Feet PN 34039
25 Feet PN 34019
100 Feet PN 34049
300 Feet PN 34059
MSD Pro-Heat Boot Guard will protect the spark plug boot from extreme exhaust temperatures. The Boot Guard is a thick, glass woven sleeve with a heavy silicone coating that provides protection against heat and abrasion.
Pro-Boot Guard,
Six feet PN 3412
The dielectric grease eases crimping and boot installation, prevents moisture buildup inside the boots and helps stop voltage leaks. Spark Guard will not dry up or harden.
Spark Guard PN 8804
This new kit will keep the plug wires in a tidy order and secure from engine heat sources. The kit is supplied with two 4-wire assmeblies, two 3-wire assemblies and four 2-wire assemblies.
Each assembly features secure grooves for each wire and a top bracket that snaps in place for a firm grip. Each Pro-Clamp can be free standing or bolted to a bracket. There is even a tab that will help hold it in position. To get the wires out, the top piece simply pries off.
MSD Pro-Clamp Kit PN 8843
These Separators are molded from strong, heat resistant polyacetal that will not crack or harden. Designed for easy removal and installation, the Separators firmly hold the wires away from the hot engine and moving components.
Up to 8.8mm Set of 16 PN 8841
Wires w/Sleeving Set of 16 PN 8842
When header clearance is tight, the MSD Pro-Heat Sleeve gives you extra insurance. This tough sleeving is made of a thick glass woven core that resists temperatures up to 1,000°F. A silicone rubber coating adds extra protection against abrasion and tearing. The sleeve slides over the plug wire for easy installation.
Pro-Heat Sleeve, 25 feet PN 3411
Replacement Boots/Terminals
Two Multi Angle Boots and Terminals
PN 3301
Two 90° Boots and Terminals
PN 3311
Two HEI Style Boots and Terminals
PN 3320 (for use with Wire Retainers)
MSD worked closely with Top Fuel racers to design our Hemi Tubes. They are molded from Rynite material for its high dielectric properties and is very durable for severe racing conditions. A 90° top housing helps route the wires without kinks or sharp bends.
Hemi Tubes 8 Red/8 Black PN 3475
100 90° MSD Boots PN 34515
100 90° Retainer Boots PN 34555
100 Multi-Angle Boots PN 34565
50 Hemi Boots (for tubes) PN 3467
This wire is 18” long and has a 90° terminal and boot on each side.
Replacement Coil Wire PN 84039
Bulk Terminals
100 Mulit-Angle Terminals
(for Hemi Boots) PN 34605
100 90° Terminals PN 34615
Always a good thing to have in the trailer! This wire is 72" long and is supplied with a Hemi boot installed along with an Insulator tube and 90° terminal and MSD boot that you install on the other end.
Replacement Wire
w/Red Hemi Tube PN 34209
Replacement Wire
w/Black Hemi Tube PN 34219For building spark plug wire sets or in custom wiring, the Pro-Crimp Tool is a necessity. The Pro-Crimp features interchangeable jaws allowing for a variety of different style crimps with one heavy duty tool.
A hardened steel frame sports comfortable molded hand grips while a slick ratchet action provides secure factory style crimps consistently. The Tool is supplied with crimp/strip jaws for MSD’s 8.5mm Dual Crimp Terminals.
Pro-Crimp Tool PN 3505
Pro-Crimp Jaws for use with the Pro-Crimp Tool only.
Amp Pin Terminal Jaws PN 3506
Amp Lug Terminal Jaws PN 3507
Plug Wire Terminal Jaws PN 3508
Weathertight Connector Terminal Jaws PN 3509
Deutsch Connector Terminal Jaws PN 3510
